-
-
If you haven't check the Z axis parts during the preflight check then you should do it now or you might have problem during this chapter.
-
Note that in this chapter you will see images of MK3(S) Y carriage but all steps are exactly the same for MK2(S) and MK2.5(S).
-
-
-
Insert 2x M5x10 screws in the z_motor_mount.
-
Engage 2x t-nuts on the M5 screws (1-2 turns) and place them vertically.
-
Repeat with the remaining z_motor_mount.
-
-
-
Make sure this section is clean of dust, it will be used as reference for the z_motor_mounts.
-
Slide the z_motor_mount from the top of the frame. Note the orientation, the hole for the Z smooth rods should face outside the frame
-
Check the orientation of your z_motor_mount or it will make the next steps impossible.
-
This step and the following ones are showing a MK3(S) Y carriage but the position is the same with MK2(S) and MK2.5(S).
-
-
-
Slide the Z motors in the z_motor_mounts. The motor cable should be oriented inside the frame (red lines on the images).
-
Secure the Z steppers in place with 8x M3x10 screws (reused from your original Prusa). Press the motor in the direction of the yellow arrows while tightening incrementally the screws.
-
Check the orientation of your motor cables.
-
You're viewing a previously published revision of this guide. View latest revision
Older
Newer
Jul 13, 2020 - 08:07:55
Apr 25, 2022 - 01:04:11
Sep 23, 2020 - 09:09:13
Sep 15, 2020 - 12:09:35
Sep 05, 2020 - 11:09:30
Sep 05, 2020 - 11:09:13
Aug 21, 2020 - 08:08:45
Aug 16, 2020 - 04:08:50
Aug 16, 2020 - 03:08:26
Aug 15, 2020 - 02:08:10
Jul 19, 2020 - 07:07:49
Jul 18, 2020 - 06:07:14
Jul 18, 2020 - 04:07:41
Jul 14, 2020 - 08:07:50
Jul 14, 2020 - 08:07:20
Jul 14, 2020 - 08:07:18
Jul 14, 2020 - 08:07:33
Jul 14, 2020 - 08:07:01
Jul 14, 2020 - 07:07:29
Jul 14, 2020 - 07:07:33
Jul 14, 2020 - 07:07:47
Jul 14, 2020 - 07:07:24
Jul 14, 2020 - 07:07:03
Jul 14, 2020 - 07:07:46
Jul 14, 2020 - 07:07:37
Jul 14, 2020 - 07:07:13
Jul 14, 2020 - 07:07:52
Jul 14, 2020 - 07:07:14
Jul 14, 2020 - 07:07:46
Jul 14, 2020 - 07:07:43
Jul 14, 2020 - 07:07:50
Jul 14, 2020 - 07:07:22
Jul 14, 2020 - 07:07:45
Jul 14, 2020 - 07:07:39
Jul 14, 2020 - 07:07:07
Jul 14, 2020 - 07:07:48
Jul 14, 2020 - 07:07:50
Jul 14, 2020 - 07:07:09
Jul 14, 2020 - 07:07:17
Jul 14, 2020 - 07:07:05
Jul 14, 2020 - 07:07:56
Jul 14, 2020 - 07:07:45
Jul 14, 2020 - 07:07:33
Jul 14, 2020 - 07:07:23
Jul 14, 2020 - 07:07:12
Jul 14, 2020 - 07:07:07
Jul 14, 2020 - 07:07:49
Jul 14, 2020 - 07:07:32
Jul 14, 2020 - 07:07:19
Jul 14, 2020 - 07:07:04
Jul 14, 2020 - 07:07:42
Jul 14, 2020 - 07:07:13
Jul 14, 2020 - 07:07:10
Jul 14, 2020 - 07:07:12
Jul 14, 2020 - 07:07:00
Jul 14, 2020 - 07:07:56
Jul 14, 2020 - 07:07:53
Jul 14, 2020 - 07:07:16
Jul 14, 2020 - 07:07:22
Jul 14, 2020 - 07:07:32
Jul 14, 2020 - 06:07:47
Jul 14, 2020 - 06:07:14
Jul 14, 2020 - 06:07:29
Jul 14, 2020 - 06:07:07
Jul 14, 2020 - 06:07:33
Jul 14, 2020 - 06:07:04
Jul 14, 2020 - 06:07:29
Jul 14, 2020 - 05:07:53
Jul 14, 2020 - 05:07:57
Jul 14, 2020 - 05:07:32
Jul 14, 2020 - 05:07:44
Jul 14, 2020 - 03:07:40
Jul 14, 2020 - 03:07:46
Jul 14, 2020 - 03:07:52
Jul 14, 2020 - 03:07:22
Jul 14, 2020 - 03:07:37
Jul 14, 2020 - 03:07:19
Jul 14, 2020 - 03:07:58
Jul 14, 2020 - 03:07:37
Jul 14, 2020 - 03:07:18
Jul 14, 2020 - 03:07:34
Jul 14, 2020 - 02:07:43
Jul 14, 2020 - 12:07:39
Jul 14, 2020 - 12:07:00
Jul 14, 2020 - 12:07:16
Jul 14, 2020 - 12:07:07
Jul 13, 2020 - 11:07:29
Jul 13, 2020 - 11:07:30
Jul 13, 2020 - 09:07:47
Jul 13, 2020 - 09:07:38
Jul 13, 2020 - 09:07:26
Jul 13, 2020 - 08:07:55
Jul 13, 2020 - 08:07:28
Jul 13, 2020 - 08:07:33
Jul 13, 2020 - 08:07:13
Jul 13, 2020 - 08:07:49
Jul 13, 2020 - 08:07:55
Jul 13, 2020 - 08:07:38
Jul 13, 2020 - 07:07:25
Jul 13, 2020 - 07:07:56
Jul 13, 2020 - 04:07:15
Jul 13, 2020 - 03:07:40
Jul 13, 2020 - 02:07:17
Jul 13, 2020 - 02:07:06
Jul 13, 2020 - 02:07:15
Jul 13, 2020 - 02:07:36
Jul 12, 2020 - 08:07:52
Jul 08, 2020 - 05:07:26
Jul 08, 2020 - 05:07:59
Jul 08, 2020 - 05:07:59
Jul 08, 2020 - 05:07:39