You're viewing a previously published revision of this guide.  View latest revision

Older
Mar 02, 2020 - 01:03:43
Jun 24, 2022 - 06:06:51 May 13, 2020 - 04:05:36 May 11, 2020 - 08:05:38 May 11, 2020 - 08:05:32 May 11, 2020 - 08:05:13 May 11, 2020 - 08:05:50 May 11, 2020 - 08:05:25 May 11, 2020 - 08:05:38 May 11, 2020 - 08:05:00 May 11, 2020 - 08:05:25 May 11, 2020 - 08:05:20 May 11, 2020 - 08:05:11 May 11, 2020 - 08:05:37 May 11, 2020 - 08:05:31 May 11, 2020 - 04:05:12 Apr 18, 2020 - 05:04:34 Apr 18, 2020 - 05:04:31 Apr 18, 2020 - 05:04:24 Apr 02, 2020 - 09:04:37 Apr 02, 2020 - 09:04:49 Apr 02, 2020 - 09:04:58 Apr 02, 2020 - 09:04:39 Apr 02, 2020 - 09:04:07 Apr 02, 2020 - 09:04:19 Apr 02, 2020 - 09:04:20 Apr 02, 2020 - 09:04:48 Apr 02, 2020 - 09:04:28 Apr 02, 2020 - 09:04:00 Apr 02, 2020 - 03:04:46 Apr 02, 2020 - 03:04:59 Apr 02, 2020 - 02:04:34 Apr 02, 2020 - 02:04:59 Apr 02, 2020 - 02:04:52 Mar 12, 2020 - 03:03:36 Mar 12, 2020 - 03:03:16 Mar 12, 2020 - 03:03:02 Mar 12, 2020 - 03:03:48 Mar 12, 2020 - 03:03:35 Mar 12, 2020 - 02:03:53 Mar 12, 2020 - 02:03:23 Mar 12, 2020 - 02:03:30 Mar 12, 2020 - 02:03:54 Mar 11, 2020 - 05:03:02 Mar 11, 2020 - 05:03:34 Mar 11, 2020 - 05:03:08 Mar 11, 2020 - 05:03:54 Mar 10, 2020 - 07:03:58 Mar 03, 2020 - 04:03:19 Mar 03, 2020 - 04:03:32 Mar 03, 2020 - 04:03:54 Mar 03, 2020 - 04:03:52 Mar 03, 2020 - 04:03:07 Mar 03, 2020 - 04:03:24 Mar 03, 2020 - 03:03:03 Mar 03, 2020 - 03:03:12 Mar 03, 2020 - 03:03:20 Mar 03, 2020 - 02:03:52 Mar 02, 2020 - 01:03:39 Mar 02, 2020 - 01:03:17 Mar 02, 2020 - 01:03:15 Mar 02, 2020 - 01:03:08 Mar 02, 2020 - 01:03:58 Mar 02, 2020 - 01:03:52 Mar 02, 2020 - 01:03:55 Mar 02, 2020 - 01:03:47 Mar 02, 2020 - 01:03:09 Mar 02, 2020 - 01:03:03 Mar 02, 2020 - 01:03:59 Mar 02, 2020 - 01:03:13 Mar 02, 2020 - 01:03:32 Mar 02, 2020 - 01:03:38 Mar 02, 2020 - 01:03:43 Mar 02, 2020 - 11:03:16 Mar 02, 2020 - 11:03:06 Mar 02, 2020 - 11:03:16
Newer

Adjustments and calibrations

Written By: Grégoire Saunier
  • Comments: 1
  • Favorites: 0
  • Completions: 3

Difficulty

Moderate

Steps

3

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

    • Let the extruder cool down.

    • Place a sheet of paper on the heated bed. Manually lower the X axis until the Hemera nozzle is touching the paper.

    • Make sure the X axis is flat (you can slowly move the Hemera left and right).

    • Loosen the PINDA locking screw and place an object of 1mm thickness under the Pinda (like the middle section of a zip tie).

    • Gently move the PINDA down until it is touching the zip tie.

    • Tighten the PINDA locking screw to secure it in place.

    • Use a plier if it is hard to reach the probe with your fingers during adjustment.

  3. Plugin and turn on the printer. Using the screen menu, move the X axis up until it crashes in to the Z tops. The stepper motors will skip. making a noise - this will not damage the motors.

    • Plugin and turn on the printer.

    • Using the screen menu, move the X axis up until it crashes in to the Z tops. The stepper motors will skip. making a noise - this will not damage the motors.

    • Using the screen menu, move the X axis down until the nozzle is approximately 10mm from the heated bed.

Author

Grégoire Saunier

Member since: 01/20/2019

22,879 Reputation

35 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 3

Past 30 Days: 16

All Time: 3,359